HP AGILENT 8510B NETWORK ANALYZER WITH HP DISPLAY PROCESSOR UNIT, HP AGILENT 8515A S-PARAMETER TEST SET, CABLES, AND MANUAL.
We calibrated the whole system. The due date is 06/12/19. The unit is in good to great cosmetic condition with a small scratch here or there. All buttons, knobs, and switches are good and intact. There are bad scratches and marks on all three unit's top cover. There are NO back and bottom feet on the Display or HP 8510B section. The serial #s are 2825A04273, 2420A00306, and 2630A01112. The Dispaly model is 85101B and 85102B with option 800 installed. Works with 120 & 240 voltage. NO other options are marked.
YOU NEED THE HP AGILENT 8350B SWEEP OSCILLATOR WITH A RF PLUG IN OR HP AGILENT 8340B/8341A/B GENERATOR TO OPERATE THIS NETWORK ANALYZER. IT WILL NOT WORK UNLESS YOU HAVE EITHER OF THESE GENERATOR! THE FREQUENCEY MAX ON THE GENERATOR IS THE MAX FREQUENCY, THE NETWORK ANALYZER WILL TAPE OUT AT! THESE GENERATORS NEED TO HAVE THE SOFTWARE, IN ORDER TO WORK WITHIN THE GPIB ON THE BACK OF THE ANALYZER.
I HAVE THE HP AGILENT 8350B WITH HP AGILENT 83594A 26.5 GHz RF PLUG IN, HP AGILENT 8341A GENERATOR WITH OPTION 05, THAT WILL WORK WITH IS HP AGILENT 8510B NETWORK ANALYZER. SOFTWARE AND EVERYTHING.
WE WILL RE-CALIBRATED THE UNIT BEFORE SHIPPING AND A NIST TRACEABLE CALIBRATION CERTIFICATE, WILL BE PROVIDED AFTER ITEM IS RECEIVED AND IS ACCEPTED AS WORKING WITH IN SPECS. WE WILL MAIL OUT THE CERTIFICATE. THE RE-CALIBRATION DELAYS THE SHIPPING TIME THREE (3) DAYS.
RE-CALIBRATION MEANS, WHEN YOU BUY THE EQUIPMENT, IT WILL BE FULLY TESTED FROM THE LOWEST TO HIGHEST FREQUENCY, dB MEASUREMENTS, ALL FUNCTIONS, AND ALL SETTINGS. NIST STANDARDS ARE USED TO CHECK THE EQUIPMENT READINGS. IT IS WITHIN THE MANUFACTURER’S SPECIFICATIONS FOR THIS PIECE OF EQUIPMENT.
The 8510 Microwave Network Analyzer provides a complete solution for characterizing the linear behavior of active or passive networks over the 45 MHz to 40 GHz range. Features include "Real Time" error-corrected measurements, 60 dB effective directive and source match, 80 dB to 100 dB dynamic range, 0.001 dB, 0.01°, and 0.01 nano-sec measurement resolution.
A complete system comprises the HP 8510B network analyzer, an S-parameter test set, and a compatible RF source. Several S-parameter test sets are available for the 8510B. The 8514B, 8515A, and 8516A test sets have a dual port architecture that develops a separate reference channel for each incident port. RF switching is done with a single built-in electronic switch.
For active device measurements, the test sets include the ability to apply DC bias (external) to the test port center conductors. The recommended system source for the 8510B is the 8360 synthesized sweeper. It provides 1 Hz frequency resolution, phase-locked narrow-band sweeps, and fully synthesized start frequencies for broadband ramp sweeps.
All 8360-series synthesized sweepers are compatible with the 8510B; however, the 83621A (20 GHz) and 83631A (26 GHz) models are optimized for 8510B system operation. Both the 8340-series synthesized sweeper and 8350B-series sweep oscillators are also compatible with the 8510B.
FEATURES AND SPECS: *** 45 MHz to 26.5 GHz coax / 100 GHz wave-guide *** Real Time error-corrected measurements *** 60 dB effective directive and source match *** 80 dB to 100 dB dynamic range *** Resolution to 0.001 dB, 0.01 degree, 0.01 ns *** GPIB.
You get the HP Agilent 8510B Display/Processor section, HP 8510B RF section, HP AGILENT 8515A S Parameter test set, Two (2) cables, Two (2) GPIB cables, and 8510 Series User Guide on CD, Service Manual on CD, Both Reference Guide on CD, and 3 power cord. NO more! Again, it passes all self test, extend board test, and will be re-calibrated.! GET THIS GREAT CALIBRATED HP AGILENT 8510B NETWORK ANALYZER WITH HP DISPLAY PROCESSOR UNIT, HP AGILENT 8515A S-PARAMETER TEST SET, CABLES, AND MANUAL TODAY!
Buy from an experienced seller.
Buyer will use there FEDEX account # for shipping. It will have to be wrapped great, and shipped in 3 different Double wall boxes for safe shipping.
PAYPAL, Bill Me Later, bank check, and personal/business check (10 day hold) is accepted. Wire transfers are good too. I do not take credit cards myself. I only take credit cards through PAYPAL!
The buyer of all re-true items will pay the shipping cost back to me, no matter the problem with the item! AGAIN, IF YOU RETURN THE ITEM TO ME, YOU WILL HAVE TO PAY THE SHIPPING COST BACK TO ME.