AAA Equipment Resources Inc
CART IS EMPTY
  » PRODUCTS
  » SERVICES PROVIDED
  » PARTS
  » SHIPPING
  » RETURN POLICY
Home > PRODUCTS

HP AGILENT 8160A 50 MHz PROGRAMMABLE PULSE GENERATOR W/OPT 020! NIST CALIBRATED!

Part Number 551
review 0 Review(s)
0
HP AGILENT 8160A 50 MHz PROGRAMMABLE PULSE GENERATOR W/OPT 020! NIST CALIBRATED!
HP AGILENT 8160A 50 MHz PROGRAMMABLE PULSE GENERATOR W/OPT 020! NIST CALIBRATED!
Email a friend Email a friend
Review this item Review this item
Price
Retail Price:  $2,500.00
Your Savings:  $501.00
Your Price:  
$1,999.00
Availability:
Back Order
Quantity
Description
HP AGILENT 8160A 50 MHz PROGRAMMABLE PULSE GENERATOR WITH OPTION 020! 

Option 020 is Second Channel.

 It was just calibrated. Date due 10/20/20. The unit is in good to great cosmetic condition. It may have a small scratch here or there. The bottom feet are missing. There is a scratch on the front readout cover by the channel readout (see picture). All buttons, knobs, and switches are good and intact. The serial # is 2827A01784. Will works with 120 & 240 voltage. NO OTHER options are marked. 

 WE WILL RE-CALIBRATED THE UNIT BEFORE SHIPPING AND A NIST TRACEABLE CALIBRATION CERTIFICATE WILL BE PROVIDED. THE RE-CALIBRATION DELAYS THE SHIPPING TIME FOUR (4) DAYS. NO DATA! DATA COST EXTRA!

 RE-CALIBRATION MEANS, WHEN YOU BUY THE EQUIPMENT, IT WILL BE FULLY TESTED FROM THE LOWEST TO HIGHEST FREQUENCY, dB MEASUREMENTS, ALL FUNCTIONS, AND ALL SETTINGS. NIST STANDARDS ARE USED TO CHECK THE EQUIPMENT READINGS. IT IS WITHIN THE MANUFACTURER’S SPECIFICATIONS FOR THIS PIECE OF EQUIPMENT.

 All operations with the HP AGILENT 8160A are microprocessor-controlled. This further simplifies operation whether performed from the front panel controls or programmed over the HP-IB. The microprocessor also enables sophisticated error detection routines to detect and display any incompatible pulse settings.  
The 8160A Programmable Pulse Generator is a top quality programmable MATE-Approved Stimuli pulse generator. With a repetition rate of up to 50 MHz and a 20 V output, the 8160A will meet all but the most demanding requirements. The 8160A is fully operable from the front-panel or via the HP-IB interface bus and can store up to 9 setups. 
The microprocessor based 8160A features a period range variable from 20 nS to 999 mS. Delay range can be set from 0.0 nS to 999 mS. Double pulse range is adjustable from 20.0 nS to 999 mS while pulse width can be varied between 10.0 nS to 999 mS. High and low output voltage ranges vary between -19.9 to 19.9 V depending on the source and load conditions.

 SPECS AND FEATURES: *** Period: 20.0 ns to 999 ms *** Width: 10.0 ns to 999 ms *** Delay: 0.00 ns to 999 ms *** Double pulse: 20 ns to 999 ms *** Output frequency (with output amplifier in use): 1 Hz to 50 MHz *** Output high level range: -9.89 V to 9.99 V *** Output low level range: -9.99 V to 9.89 V *** Amplitude: 0.10 V minimum, 9.99 V maximum *** Accuracy: 1% of programmed value ±50 mV ±1% of amplitude *** Settling time: 40 ns to specified accuracy *** Transition times: 06.0 ns to 9.99 ms *** Operating modes: NORM: Continuous pulse stream GATE: External signal enables rate generator. First output pulse sync with leading edge. Last pulse always complete TRIG: Each input cycle generates a single output pulse BURST: Each input cycle generates a programmable number (0 to 9999) of pulses - Minimum time between burst is one period MAN: Simulates external signal with EXT INPUT switched OFF SINGLE PULSE: Provides a single pulse independent of input and period settings *** External input: Trigger level: +10 to -10 V Maximum input: ±12 V in 50 O, ±20 V in 10 kO Minimum amplitude: 500 mVpp Slope: positive or negative Minimum pulse width: 3 ns Typical input resisitance: 50 O or (also in OFF) 10 kO Delay from trigger input to trigger output: 90 ns ±10 ns *** Trigger output: Output amplitude: =2.5 V into 50 O, =5 V into open circuit Typical source resistance: 50 O Typical pulse width: 8 ns (PER < 100 ns), 40 ns (100 ns < PER < 1 µs), 400 ns (PER = 1 µs) *** HP-IB interface *** OPTION 020 = Second Channel.

  You get HP AGILENT 8160A GENERATOR, Operating and Service Manual on CD, User Ref on CD, and power cord. NO more. Again, it was tested and works fine! GET THIS GREAT WORKING CALIBRATED, HP AGILENT 8160A 50 MHz PROGRAMMABLE PULSE GENERATOR WITH OPTION 020 TODAY! 

Buy with confidence as feedback speaks for itself. 

Buyer pays $140.00 shipping in 48 states with insurance. Overseas will cost more. We will bubble wrap it great and put in a double wall box for safe shipping. We do not use eBay Global shipping.

 PAYPAL, bank check, and personal/business check (10 day hold) is accepted. Wire transfers are good too. I do not take credit cards myself. I only take credit cards through PAYPAL! All Paypal purchases must be deliver to a confirmed address.

Related Items
TEKTRONIX 2467B 4 CHANNEL/ 400 MHz OSCILLOSCOPE W/ EXTRAS!   NIST CALIBRATED !
TEKTRONIX 2467B 4 CHANNEL/ 400 MHz OSCILLOSCOPE W/ EXTRAS! NIST CALIBRATED !
Average Rating 0 Review(s)
Your Price: $900.00
  
Browse Similar Items